Tell us about your vision, and we’ll create a seamless solution for your home.

Monday, October 19, 2026
A long-term client wanted more bass. The answer was 3 dB, not a new pair of subwoofers.
A few weeks ago, one of Hutter Home Theater's long-term clients sent a text. "David, can you price out some new subwoofers for me? I really want to feel the bass."
This is a client David Hutter has worked with for years. Hutter Home Theater built his first surround system, a 5.1 setup. Later the company upgraded him to a full 7.2.4 Dolby Atmos theater with a JVC 8K projector and high-end KEF speakers, including a pair of KEF subwoofers.
So when he asked for new subs, the easy answer was yes. Price out a few options, pick one, send an invoice.
Hutter Home Theater did price them out. Then it did something most integrators would not do. It asked why.
What followed is a good example of why a proper home theater subwoofer calibration and room evaluation should come before any new gear is purchased. In this case it saved the client the cost of two subwoofers he did not need
Hutter started by quoting three options.
SpeakerCraft. The top of their line. Dual 1,000-watt amplifiers in each sub, sealed cabinet, rated down to 17 Hz. With two of them, that is 4,000 watts of bass in the room.
KEF. A higher-tier model than what the client already owned, quoted mainly to offer another option. Roughly double the price of the SpeakerCraft with similar performance and 1,000 watts per sub.
Triad. The least expensive of the three. Still rated to about 17 Hz with 1,000 watts per sub, which in a normal residential room is more than enough. For reference, a pair of 500-watt subs will do the job in most decent-sized rooms.
The client asked to add two more brands he had been reading about: SVS and JL Audio. So Hutter built a spreadsheet comparing all five. Power, frequency response, cabinet type, size, price, pros and cons. The kind of comparison a client can actually use to make a decision.
All five are good products. Any of them would have worked. That was the problem.
While looking up specs for the KEF option, Hutter checked the specs on the subs the client already had.
They go down to 11 Hz.
That is lower than every subwoofer on the spreadsheet. The client already owned subs with better low-end reach than anything being quoted. The only real advantage the SpeakerCraft had was raw power, and two 1,000-watt subs is already plenty for his room.
So Hutter asked the question. Why do you want new subwoofers?
The answer was the same as the text message. He wanted to feel the bass more.
That is not a gear problem. That is a setup problem, or a room problem, or a preference problem. None of those are fixed by buying new equipment. Hutter told him: before we buy anything, let me come out, set up the measurement equipment, and see what is actually happening in the room.
The morning of the visit, the client mentioned one more thing. His JVC 8K projector had stopped showing a picture.
That had to be solved first, because audio calibration needs the display working. The test patterns and the processor menus all live on screen.
The HDMI cable running to the projector is a fiber optic cable rated for 48 Gbps. Those do not fail on their own, so Hutter did not start there. He pulled the cable at the projector end and connected it straight to the Roku streaming device. Still no picture. That pointed at the projector, not the signal chain.
He unplugged the projector, let it sit, and powered it back up. The picture came back.
Sometimes the fix is a reboot. The value is in knowing what to rule out first so you do not spend an hour chasing a cable that was never the problem.
With the picture back, Hutter set up the calibration equipment at the main listening position and ran the measurements.
The first thing to rule out was a null.
A null is a spot in the room where sound waves from the subwoofer cancel each other out. Bass bounces off walls, and when a reflected wave meets the direct wave out of phase, they subtract. At certain frequencies, in certain seats, the bass just disappears.
Here is the part most people do not understand about nulls. You cannot fix one with more power. Zero times one is zero. Zero times fifty is still zero. If the couch is sitting in a null, the client could buy the biggest subwoofers on the market and still not feel much of anything in that seat. The only fixes are moving the subs, moving the seat, or treating the room.
That is why this had to be measured before anything was bought. If the couch was in a null, new subwoofers would have been a waste of money.
The measurements came back clean. The subs were placed well. The listening position was not in a null. The system was doing what it was designed to do.
So Hutter went into the processor and raised both subwoofer channels by 3 decibels.
That is a small number. It was also a noticeable change. The client sat down, played a scene, and heard exactly what he had been asking for.
A note on why that works. A standard calibration sets every channel, including the subs, to the same reference level. That is the correct starting point, and it is how Hutter Home Theater calibrates every system. But a reference level is not a rule. It is a baseline. Some clients want the bass a little hotter than reference, and that is a valid preference. It is their room. The calibration gives you a known, measured starting point, and from there you can adjust with intent instead of guessing.
The client did not buy new subwoofers. He did not need them. He got the result he wanted from a measured adjustment to gear he already owned.
Before Hutter left, the client asked for quotes on two more theaters, one for the master bedroom and one for the bonus room.
That is not a coincidence. It is the whole business model. Hutter Home Theater has been almost entirely referral-based for 25 years, and referrals come from clients who trust that the advice they get is in their interest, not the invoice's.
An integrator who sells the subwoofers makes one sale. An integrator who measures the room first and says "you do not need these" earns the next three projects.
None of this is possible without the measurement equipment and the training to use it. Hutter holds HAA (Home Acoustics Alliance) Level 2 certification for audio calibration, THX certifications in audio calibration, video calibration, and home theater design, and ISF (Imaging Science Foundation) certification for video. Without the gear, there is no way to know whether a seat is in a null, whether placement is right, or whether the problem is simply a few decibels of preference. You would be guessing. And guessing usually ends with buying something.
That training is not a one-time thing. Hutter has taken extensive home theater design coursework through CEDIA, the Custom Electronic Design and Installation Association. When he upgraded his calibration system in 2021, an iPad-based platform with dedicated measurement hardware, HAA training on the software and tools was required before he could put it to work.
The same approach runs through every audio and video system Hutter Home Theater designs, and through the automation that ties a theater to the rest of the house. Measure first. Then decide.
Lorem ipsum dolor sit amet, consectetur adipisicing elit. Autem dolore, alias, numquam enim ab voluptate id quam harum ducimus cupiditate similique quisquam et deserunt, recusandae.
If your theater does not sound the way you expected, the answer might not be new equipment. It might be a measurement you have never had done. Hutter Home Theater serves luxury homeowners across the Seattle-Tacoma area, from Gig Harbor to Bellevue to Medina.
Take just 3 quick questions and Hutter Home Theater will show you what is possible for your home.

Founder, Hutter Home Theater
Most of my work comes through referrals, and this blog is a way to share my knowledge with more families in the Seattle–Tacoma area. If you’re ready for a theater, smart lighting, or whole-home automation, I’d love to help you get started.
From custom theaters to smart home automation, I’ll help design a system tailored to your lifestyle. Let’s talk about your vision and bring it to life.
Subscribe to get the latest articles, updates, and tips delivered straight to your inbox.
We’ll only send relevant updates. Unsubscribe anytime.


© 2026 Hutter Home Theater. All Rights Reserved.